HeatEx Direct

HT-BLOC Welded Plate Heat Exchanger: In-Depth Analysis of Core Technology and Manufacturing

Author: Shanghai Heat Transfer Equipment Co., Ltd.
Read: 9 minutes
HT-BLOC Welded Plate Heat Exchanger: In-Depth Analysis of Core Technology and Manufacturing

1. The Engineering Challenge: Overcoming the Limits of Traditional Heat Exchangers

In modern process industries, especially refining, chemicals and power generation, engineers face a critical conflict: the need for higher energy efficiency and lower emissions on one side, and the physical limits of traditional heat exchangers on the other.

  • Shell-and-tube heat exchangers: reliable, but with low heat transfer efficiency and a very large footprint.
  • Gasketed plate heat exchangers (GPHE): efficient, but limited by gasket failure at high pressure (above 25 bar) or high temperature (above 180 °C).

Shanghai Heat Transfer Equipment Co., Ltd. (SHPHE) offers the HT-BLOC welded plate heat exchanger. It eliminates gaskets entirely and combines high efficiency with durability, resolving the industry's "efficiency versus safety" dilemma.

2. Technical Analysis: Why Traditional Designs Fall Short

To understand the advantage of the HT-BLOC, it helps to look at the built-in bottlenecks of traditional heat exchangers.

2.1 Limitations of Shell-and-Tube Units

Despite their popularity, shell-and-tube designs have systemic inefficiencies:

  • Laminar sublayer resistance: the flow needs a high velocity (Re > 2,300) to break the laminar boundary layer inside the tubes.
  • Shell-side dead zones: baffles create dead zones and bypass streams where hardly any heat is transferred.
  • Low K values: the overall heat transfer coefficient (K value) is typically 200–2,000 W/m²·K, so a large surface area and a large footprint are needed to meet the duty.

2.2 Limitations of Gasketed Plate Units

Gasketed plate heat exchangers are efficient (K values up to 7,000 W/m²·K), but their sealing method limits them:

  • Material failure: rubber gaskets (EPDM, NBR, FKM) degrade quickly at high temperatures or in aggressive chemicals such as aromatics and solvents.
  • Leakage risk: thermal cycling causes gasket fatigue, which can lead to serious leaks in hazardous services.

3. The HT-BLOC Solution

Against this background, SHPHE's HT-BLOC welded plate heat exchanger addresses all of the limitations above. Its structural design combines the robustness of tubular units with the efficiency of plate units.

3.1 Core Structure: "Robust Core, Flexible Shell"

  • Fully welded plate pack: the heat transfer core is laser or plasma welded, forming a gasket-free pressure vessel. It handles temperatures from −50 °C to 400 °C and pressures from vacuum to 4.0 MPa.
  • Frame that opens on four sides: unlike fully enclosed plate-and-shell units, the HT-BLOC has removable panels on all four sides, so the flow channels can be cleaned mechanically, for example by high-pressure water jetting. This is essential in fouling-prone process services.

3.2 Technology Comparison: HT-BLOC vs. Traditional Units

FeatureGasketed plate heat exchangerShell-and-tube heat exchangerSHPHE HT-BLOC
SealingRubber gaskets (prone to leaks)Welded or gasketedFully welded (no gaskets)
Heat transfer efficiencyHigh (K = 3,000–7,000)Low (K = 200–2,000)High (K = 3,000–7,000)
Pressure / temperature limits< 25 bar / < 180 °CHigh / highVacuum to 40 bar / −50 °C to 400 °C
CleanabilityEasy (plate pack can be opened)Difficult (tube side only)Accessible (removable panels)
FootprintCompactLargeCompact (about 1/4 of a tubular unit)

4. Core Design: Flow Dynamics and Channel Optimization

A key reason for the HT-BLOC's thermal performance is its plate design, which controls fluid flow behavior at a very fine scale. Drawing on decades of industry experience and extensive computational fluid dynamics (CFD) simulation, SHPHE has continuously refined the corrugation of its heat transfer plates and optimized the overall flow distribution.

4.1 How Corrugated Plates Increase Turbulence

The HT-BLOC plate has a specially formed chevron (herringbone) corrugation pressed into its surface.

Chevron corrugated heat transfer plate
  • Turbulence at low Reynolds numbers: in smooth round tubes, flow usually changes from laminar to turbulent when the Reynolds number (Re) exceeds 2,300. In the complex corrugated channels of the HT-BLOC, the fluid changes direction constantly, which creates strong secondary flow and vortices. Turbulence starts at a Reynolds number as low as 1,000.
  • Breaking up the boundary layer: turbulence not only improves mixing across the channel but, more importantly, keeps breaking up the laminar sublayer at the plate wall, which is the main source of thermal resistance. Removing this thin layer sharply raises the overall heat transfer coefficient, typically to 3–5 times that of a shell-and-tube heat exchanger.
  • Self-cleaning by shear: strong turbulence produces high wall shear stress on the plate surface. This shear scours away fouling particles before they can stick, which greatly reduces the fouling factor and extends the cleaning interval.

4.2 Flexible Flow Arrangements: Counterflow and Multi-Pass Design

Shell-and-tube heat exchangers have fixed flow arrangements that are hard to change once built. The HT-BLOC offers much more engineering flexibility.

  • True counterflow: in multi-pass designs, the HT-BLOC provides true counterflow between the hot and cold fluids. Counterflow is critical for high heat recovery: it allows the cold fluid to leave at a higher temperature than the hot fluid's outlet temperature (a temperature cross). In water-to-water service, the approach temperature can be as low as 3 °C.
  • Asymmetric passes: partition plates in the headers let the hot and cold sides have different numbers of passes. For example, the high-flow side can be single-pass while the low-flow side is multi-pass. This balances velocity and pressure drop on both sides and optimizes overall heat transfer.

5. Core Manufacturing: Welding Process Control

In a fully welded plate heat exchanger, the quality of the welds at the plate edges directly determines service life and corrosion resistance. There are two mainstream methods: lap welding and butt welding. For the HT-BLOC, SHPHE uses butt welding, which is more complex but performs far better.

Diagram of two ways to weld plate edges

5.1 The Risks of Lap Welding

Many low-cost all-welded heat exchangers use lap welding, where the edges of two plates are overlapped and then welded.

  • What happens at the micro level: the overlap creates tiny crevices between the plates.
  • How corrosion develops: in corrosive media such as chloride-containing cooling water, the fluid inside the crevice becomes stagnant. As corrosion proceeds, the oxygen in the crevice is quickly used up while the outside stays oxygen-rich. The metal inside the crevice becomes the anode and the metal outside the cathode, forming an active oxygen concentration cell.

5.2 SHPHE's Butt Welding Solution

The SHPHE HT-BLOC uses plasma or laser welding to fuse the plate edges edge to edge.

  • No dead zones: the butt weld is flush with the surface of the base metal, so there is no physical crevice and no crevice corrosion. Fluid flowing over the weld keeps it scoured and prevents stagnant zones. This removes the conditions that crevice corrosion needs.
  • Fatigue resistance: under alternating temperature or pressure loads, lap joints have severe stress concentration at the weld root because of their geometric discontinuity, which makes them prone to fatigue cracking. Butt welds have smooth, even stress flow lines, and their fatigue strength is close to that of the base metal.
  • Reliable quality: SHPHE's automated welding line and strict non-destructive testing (NDT), including penetrant testing (PT) and helium leak testing, ensure that the penetration and integrity of every weld meet nuclear-grade safety standards and the strict requirements of the ASME U stamp.

6. Solutions for Difficult Services: The HT-BLOC Wide-Gap Series

In industries such as papermaking, alumina production and fermentation, process fluids often contain many fibers, solid particles or crystals. The narrow channels (2–5 mm) and dense contact points of standard plate heat exchangers clog easily. To solve this, SHPHE developed the HT-BLOC wide-gap series.

  • Wide-gap channels: the channel gap ranges from 6 mm to 30 mm, so fluids containing large particles or long fibers can flow freely.
  • Pillar or dimpled pattern: instead of the point-to-point contacts of conventional chevron corrugations, wide-gap plates use pillar or dimpled supports. This greatly reduces the number of contact points and removes the anchor points where fibers tangle, so the fluid flows more smoothly.
Dimpled plate pattern used in wide-gap plates
  • Free-flow design: for extremely dirty, fouling-prone fluids, SHPHE offers a free-flow design with no or very few contact points, which eliminates the risk of clogging.

Typical applications:

  • Alumina industry: spent liquor and red mud slurry. The wide-gap design lets slurries with a high solids content pass while keeping heat transfer high, replacing bulky, inefficient shell-and-tube or spiral heat exchangers.
  • Papermaking and fermentation: fiber-containing black liquor and fermentation mash. The fully welded structure prevents odor leaks, and the wide channels stop fibers from sticking to the plates and clogging them.
  • Crude oil cooling: as a crude oil cooler, the wide-gap design resists sediment and wax deposits. With the removable frame panels, mechanical cleaning is simple.

7. Quality Assurance and Life-Cycle Value

The SHPHE HT-BLOC is designed and built in strict compliance with international standards:

  • Design standards: API 662 / ISO 15547 (plate heat exchangers for the petroleum, petrochemical and natural gas industries) and the ASME Section VIII Division 1 pressure vessel code.
  • Certifications: ASME U stamp, NB registration, EU CE (PED), and third-party approvals from BV and SGS.
  • Inspection: every unit undergoes strict non-destructive testing (NDT), including radiographic testing (RT) and penetrant testing (PT), plus a hydrostatic pressure test before delivery.

Total Cost of Ownership (TCO)

Looking at life-cycle cost (LCC) instead of only the purchase price (CAPEX) shows the real value of the HT-BLOC:

  • Lower CAPEX: high efficiency means less surface area. Even in high-grade materials such as titanium or Hastelloy, the total cost is often lower than that of a bulky carbon steel tubular unit.
  • Lower OPEX: the compact size cuts installation and civil costs, high heat recovery lowers energy bills, and the accessible design minimizes maintenance downtime.

8. Conclusion: A Technology Upgrade for the Process Industry

The HT-BLOC is more than a replacement for traditional heat exchangers. It is a targeted technology upgrade for the global process industry, in line with the industry's pursuit of carbon neutrality and operational excellence. The HT-BLOC combines the safety of a fully welded core with the easy maintenance of a removable frame. Through optimized channel design and precise control of butt welding, it removes corrosion and fouling risks at the source. For refineries, chemical plants and power stations working toward carbon neutrality and operational excellence, the HT-BLOC is an excellent choice that balances thermal performance with long-term, safe operation.

Appendix: Technical Specifications

ParameterSpecification
Max. area per unit900 m²
Plate thickness0.8–2.0 mm
Design pressureVacuum to 4.0 MPa (40 bar)
Design temperature−50 °C to +400 °C
Plate materials304/304L, 316/316L, 904L, 254SMO, Hastelloy C-276, titanium
Connection sizeDN25 to DN1000
CertificationsASME U, NB, CE, BV, CCS, SGS, ISO 9001
Need equipment like this?
Send one request with your operating conditions. We review it and pass it to suitable Chinese manufacturers.
View the Shanghai Heat Transfer Equipment Co., Ltd. profile
Request a Quote